on video 4 Lights Control With Twin Timer

 4 Lights Control With Twin Timer

Wiring Digital Twin Timer for ON/OFF Delay Operations in 120 and 240V Circuits

As the name suggests, a digital twin timer performs dual operations in a single circuit. It can be wired and configured for one-shot operation or a repeated ON/OFF delay mechanism. In today’s wiring tutorial, we will learn how to wire a twin timer to control 120V and 240V load circuits for ON and OFF delay operations.

Before going into details, let’s examine the internal wiring connections and terminals of twin timers, such as Inkbird twin timers, Omron DH48S-S, Sestos twin timers, H3CR-F solid-state twin timers, etc.

Wiring Twin Timer for OFF-Delay

As a general setup, the power supply (120V-240V AC) is connected to the 2 and 7 terminals via Neutral and Line (Hot). The hot wire is connected to the 8 terminal through a jumper wire from 7. The load is connected to the 5-NC terminal of the twin timer.

When the timer is connected to the power supply, it activates, and the timer starts to count the preset time. When it reaches the predefined time interval (in seconds, minutes, or hours), its 5 – NC contact opens and closes with 6 – NO. This way, the light turns OFF.

When the power is disconnected from the timer, it deactivates and reactivates the sequence when power is restored to the timer circuit.

Wiring Twin Timer for ON-Delay

The wiring configuration for the ON-delay using a twin timer is the same as above, except the light bulb is connected to the 6 – NO terminal instead of the 5 – NC. Hence, the circuit operation is reversed, and the load will turn on after the delay time expires in the twin timer.

Wiring Twin Timer for Double Operations

As the twin timer has two timer functions, T1 (timer 1) and T2 (timer 2), the time settings in seconds, minutes, and hours can be set up for both circuits. Wire the circuit as shown in the following diagram. Now, let’s see how it works.

For example, the time setting for both light bulbs is 5 seconds (you may use other time setting based on the circuit requirement): 5 seconds of OFF-delay for the Blue light bulb connected to the 6 – NO terminal and 5 seconds of ON -delay for the Red light bulb connected to the 5 – NC terminal of the twin timer.

When the circuit is activated by providing a power supply of 120/240V AC to the timer, it will start counting. After counting for 5 seconds, the blue light bulb will turn ON, and the red light bulb will turn OFF.

The Red push button is used to reset the circuit. For instance, when the timer starts counting the predefined time period, if the operator presses the red push button, the timer will reset and start the time from the beginning, i.e., from zero.

If the operator presses the green push button, it will pause the circuit, meaning the timer will stop counting the time until the green push button is released.

 4 Lights Control With Twin Timer

Wiring Digital Twin Timer for ON/OFF Delay Operations in 120 and 240V Circuits

As the name suggests, a digital twin timer performs dual operations in a single circuit. It can be wired and configured for one-shot operation or a repeated ON/OFF delay mechanism. In today’s wiring tutorial, we will learn how to wire a twin timer to control 120V and 240V load circuits for ON and OFF delay operations.

Before going into details, let’s examine the internal wiring connections and terminals of twin timers, such as Inkbird twin timers, Omron DH48S-S, Sestos twin timers, H3CR-F solid-state twin timers, etc.

Wiring Twin Timer for OFF-Delay

As a general setup, the power supply (120V-240V AC) is connected to the 2 and 7 terminals via Neutral and Line (Hot). The hot wire is connected to the 8 terminal through a jumper wire from 7. The load is connected to the 5-NC terminal of the twin timer.

When the timer is connected to the power supply, it activates, and the timer starts to count the preset time. When it reaches the predefined time interval (in seconds, minutes, or hours), its 5 – NC contact opens and closes with 6 – NO. This way, the light turns OFF.

When the power is disconnected from the timer, it deactivates and reactivates the sequence when power is restored to the timer circuit.

Wiring Twin Timer for ON-Delay

The wiring configuration for the ON-delay using a twin timer is the same as above, except the light bulb is connected to the 6 – NO terminal instead of the 5 – NC. Hence, the circuit operation is reversed, and the load will turn on after the delay time expires in the twin timer.

Wiring Twin Timer for Double Operations

As the twin timer has two timer functions, T1 (timer 1) and T2 (timer 2), the time settings in seconds, minutes, and hours can be set up for both circuits. Wire the circuit as shown in the following diagram. Now, let’s see how it works.

For example, the time setting for both light bulbs is 5 seconds (you may use other time setting based on the circuit requirement): 5 seconds of OFF-delay for the Blue light bulb connected to the 6 – NO terminal and 5 seconds of ON -delay for the Red light bulb connected to the 5 – NC terminal of the twin timer.

When the circuit is activated by providing a power supply of 120/240V AC to the timer, it will start counting. After counting for 5 seconds, the blue light bulb will turn ON, and the red light bulb will turn OFF.

The Red push button is used to reset the circuit. For instance, when the timer starts counting the predefined time period, if the operator presses the red push button, the timer will reset and start the time from the beginning, i.e., from zero.

If the operator presses the green push button, it will pause the circuit, meaning the timer will stop counting the time until the green push button is released.