Tp5100 module kit review video, tp5100 se battery charging
Input voltage: DC 5-18V(actual 5-12V is appropriate)
Charging status: full and no-load blue light, red during charging
The voltage setting must be operated in the power-off state, and the switch must be disconnected before switching.
Characteristic:
1. Dual/single 8.4V/4.2V lithium battery charging
2. Built-in power MOSFET, switch mode, low device heat, simple external
3. Programmable charge current, 0.1-2A
4. Programmable precharge current, 10%-100%
5. No need for an external anti-sinking schottky diode
6. Wide operating voltage up to 18V
7. Red and blue LED charge status indication
8. Chip temperature protection, over-current protection, under-voltage protection
9. Battery temperature protection, reverse battery shutdown, short circuit protection
10. Switching frequency 400KHz, available inductance 20uH and above
11. PWR_ 0N-power, battery-powered switching control
12. Less than 1% charge voltage control accuracy
13. Trickle, constant current, constant voltage three-stage charging to protect the battery
14. Using QFN16 4mm*4mm ultra small package
Absolute maximum rating:
1. Static input supply voltage (vin): 20V
2. BAT: -8.4V~20V
3. BAT short circuit duration: continuous
4. Maximum junction temperature: 120℃
5. Working environment temperature range: -40℃~85℃
6. Storage temperature range: -65℃~125℃
7. Pin temperature (welding time 10 seconds): 260'℃
DISCLAIMER: Unless otherwise stated all products shown in this video have been personally purchased. The description and video may contain links to products which might be affiliate links, so if you click on one of the product links I could receive a small commission. This does not affect the price you pay. If you do purchase through my affiliate link this will help fund future videos, thank you for your support!
Tp5100 module kit review video, tp5100 se battery charging
Input voltage: DC 5-18V(actual 5-12V is appropriate)
Charging status: full and no-load blue light, red during charging
The voltage setting must be operated in the power-off state, and the switch must be disconnected before switching.
Characteristic:
1. Dual/single 8.4V/4.2V lithium battery charging
2. Built-in power MOSFET, switch mode, low device heat, simple external
3. Programmable charge current, 0.1-2A
4. Programmable precharge current, 10%-100%
5. No need for an external anti-sinking schottky diode
6. Wide operating voltage up to 18V
7. Red and blue LED charge status indication
8. Chip temperature protection, over-current protection, under-voltage protection
9. Battery temperature protection, reverse battery shutdown, short circuit protection
10. Switching frequency 400KHz, available inductance 20uH and above
11. PWR_ 0N-power, battery-powered switching control
12. Less than 1% charge voltage control accuracy
13. Trickle, constant current, constant voltage three-stage charging to protect the battery
14. Using QFN16 4mm*4mm ultra small package
Absolute maximum rating:
1. Static input supply voltage (vin): 20V
2. BAT: -8.4V~20V
3. BAT short circuit duration: continuous
4. Maximum junction temperature: 120℃
5. Working environment temperature range: -40℃~85℃
6. Storage temperature range: -65℃~125℃
7. Pin temperature (welding time 10 seconds): 260'℃
DISCLAIMER: Unless otherwise stated all products shown in this video have been personally purchased. The description and video may contain links to products which might be affiliate links, so if you click on one of the product links I could receive a small commission. This does not affect the price you pay. If you do purchase through my affiliate link this will help fund future videos, thank you for your support!
No comments:
Post a Comment