Today I am going to make a circuit of continuity tester.Using this circuit we can test continuity of many components like as Diode, LED etc.This circuit I will make using BC547 transistor.
Latch basically means “to become fixed in a particular state”. In Electronics, Latch Circuit is a circuit which locks its output, when a momentarily input trigger signal is applied, and retains that state, even after the input signal is removed. This State will remain indefinitely until the power is reset or some external signal is applied. Latch circuit is similar like SCR (Silicon Controlled Rectifier) and can be very useful in alarm circuits, where a small trigger signal will Turn On the alarm for indefinite period, until reset manually. We have previously built some alarm circuits:
Laser Security Alarm Circuit
Fire Alarm using Thermistor
Burglar Alarm Circuit
IR Based Security Alarm
Fire Alarm System using AVR Microcontroller
Today we are going to build a very simple and cheap Latch circuit using Transistors, this circuit can be used to trigger the AC mains loads and alarms.
Components:
Resistors- 10k (2), 100k (2), 220 ohm (1)
Transistors- BC547, BC557
Capacitor- 1uF
Relay-6v
Diode-1N4148
LED
Power Source- 5v-12v
Circuit Diagram:
Circuit Diagram of Latching circuit is simple and can be easily built. Resistor R1 and R4 work as a current limiting resistor for Transistor Q1 and resistors R2 and R3 work as a current limiting resistor for Transistor Q2. Current Limiting resistors must be used at the bases of BJT transistors, otherwise they might burn. Purposes of other components have been explained in ‘Working section’ below.
Working Explanation:
Before going into the explanation, we should note that Transistor Q1 BC547 is a NPN transistor, which conducts or Turns On, when a small positive voltage is applied to its base. And Transistor BC557 is PNP transistor which Conducts or Turns On, when a negative voltage (or ground) is applied to its base.
Initially, both the transistors are in OFF state, and Relay is deactivated. PNP Transistor BC557 base is connected to Positive voltage with current limiting resistor R3, so that it won’t conducts accidently. Capacitor C1 has been used precautionary, to prevent the accidental and false triggering of the circuit.
Now when a small positive voltage is applied to the Base of Transistor BC547, it turns ON the transistor and Base of the transistor Q2 BC557 gets connected to the Ground. Resistor R2 and R3 prevents the short circuit in this condition. Now when Base of Transistor BC557 gets grounded, it starts conducting and energises the Coil of relay, which activates the Relay and turns ON the device connected to Relay. In our case LED will glow.
This is normal behavior until now, but what makes it a ‘Latch’ circuit. If you notice, collector of Transistor BC557 is connected to the base of Transistor BC547, through a current limiting resistor R4. And when the Transistor BC557 turns ON, current flows in two directions, first to the relay and second to the base of transistor Q1. So this Feedback voltage to the base of Transistor BC547, keeps the transistor BC547 ON for indefinite period, even after the input trigger voltage is removed. This in turns keeps the second transistor ON indefinitely and a Latch or Lock is formed instantly.
Now the alarm or device, connected to the Relay, will remain ON until the Power is reset. Or a Reset Push button can be added to this circuit, to break the Latch state. This button would connect the base of transistor BC547 to the Ground, which turns OFF the Q1 and Q2, and breaks the Latch.
If you do not want to Latch any AC appliances, and just want Turn ON LED or a Buzzer, you can simply remove the Relay and connect the LED directly in place of the Relay, with a resistor.
Diode 1N4148 is used to prevent reverse current flow, when the transistor is switched OFF. Each Inductor coil (in Relay) produces equal and opposite EMF when switched OFF suddenly, this may cause permanent damage to components, so Diode must be used to prevent reverse current. Understand the Working of Relay here.
Today I am going to make a circuit of continuity tester.Using this circuit we can test continuity of many components like as Diode, LED etc.This circuit I will make using BC547 transistor.
Latch basically means “to become fixed in a particular state”. In Electronics, Latch Circuit is a circuit which locks its output, when a momentarily input trigger signal is applied, and retains that state, even after the input signal is removed. This State will remain indefinitely until the power is reset or some external signal is applied. Latch circuit is similar like SCR (Silicon Controlled Rectifier) and can be very useful in alarm circuits, where a small trigger signal will Turn On the alarm for indefinite period, until reset manually. We have previously built some alarm circuits:
Laser Security Alarm Circuit
Fire Alarm using Thermistor
Burglar Alarm Circuit
IR Based Security Alarm
Fire Alarm System using AVR Microcontroller
Today we are going to build a very simple and cheap Latch circuit using Transistors, this circuit can be used to trigger the AC mains loads and alarms.
Components:
Resistors- 10k (2), 100k (2), 220 ohm (1)
Transistors- BC547, BC557
Capacitor- 1uF
Relay-6v
Diode-1N4148
LED
Power Source- 5v-12v
Circuit Diagram:
Circuit Diagram of Latching circuit is simple and can be easily built. Resistor R1 and R4 work as a current limiting resistor for Transistor Q1 and resistors R2 and R3 work as a current limiting resistor for Transistor Q2. Current Limiting resistors must be used at the bases of BJT transistors, otherwise they might burn. Purposes of other components have been explained in ‘Working section’ below.
Working Explanation:
Before going into the explanation, we should note that Transistor Q1 BC547 is a NPN transistor, which conducts or Turns On, when a small positive voltage is applied to its base. And Transistor BC557 is PNP transistor which Conducts or Turns On, when a negative voltage (or ground) is applied to its base.
Initially, both the transistors are in OFF state, and Relay is deactivated. PNP Transistor BC557 base is connected to Positive voltage with current limiting resistor R3, so that it won’t conducts accidently. Capacitor C1 has been used precautionary, to prevent the accidental and false triggering of the circuit.
Now when a small positive voltage is applied to the Base of Transistor BC547, it turns ON the transistor and Base of the transistor Q2 BC557 gets connected to the Ground. Resistor R2 and R3 prevents the short circuit in this condition. Now when Base of Transistor BC557 gets grounded, it starts conducting and energises the Coil of relay, which activates the Relay and turns ON the device connected to Relay. In our case LED will glow.
This is normal behavior until now, but what makes it a ‘Latch’ circuit. If you notice, collector of Transistor BC557 is connected to the base of Transistor BC547, through a current limiting resistor R4. And when the Transistor BC557 turns ON, current flows in two directions, first to the relay and second to the base of transistor Q1. So this Feedback voltage to the base of Transistor BC547, keeps the transistor BC547 ON for indefinite period, even after the input trigger voltage is removed. This in turns keeps the second transistor ON indefinitely and a Latch or Lock is formed instantly.
Now the alarm or device, connected to the Relay, will remain ON until the Power is reset. Or a Reset Push button can be added to this circuit, to break the Latch state. This button would connect the base of transistor BC547 to the Ground, which turns OFF the Q1 and Q2, and breaks the Latch.
If you do not want to Latch any AC appliances, and just want Turn ON LED or a Buzzer, you can simply remove the Relay and connect the LED directly in place of the Relay, with a resistor.
Diode 1N4148 is used to prevent reverse current flow, when the transistor is switched OFF. Each Inductor coil (in Relay) produces equal and opposite EMF when switched OFF suddenly, this may cause permanent damage to components, so Diode must be used to prevent reverse current. Understand the Working of Relay here.
No comments:
Post a Comment