Prior to the final installation you should first take time to understand the working of this water level controller, Model- 1A_0020
Things you’ll need for this DIY test:
Water level controller
Two pcs of small wire
Screw driver
Electrical bulb with holder and wire ( For demo instead of Motor)
Steps to follow:
Connect 220V Ac supply at input terminals. Phase–P, Neutral–N
Connect electrical bulb at output terminals (Both Phase & Neutral)
Switch ON the power supply and keep the black switch in OFF position
Connect the one end of both wires and connect that end at L0.
Turn the switch position to AUTO –> As Green sensor is not connected Motor On Led is ON and Bulb is ON (i.e water level is low)
Connect one wire end at L1 —> 1st Led (25% level) will glow
Connect/ Touch other wire at L2 as shown in video —> Top Level Led (100% level) will glow & Motor On Led will be OFF & Bulb will also be OFF ( tank is Full )
Now turn the switch to Bypass Position –> Motor Led is ON i.e Bulb is ON irrespective of water level in the tank in Bypass Mode
Detailed video of How to Install IoTfiers – Water Level Controller (Model 1A_0020)
IoTfiers Fully automatic water level controller is suitable for Single Phase Submersible pumps (Borewell Type) upto 2 Hp with MCB type starter ( i.e Single Capacitor type starter). It requires no manpower to operate as it switches ON the motor when tank level is low (as soon as water falls below Green sensor) and automatically switches it OFF when the tank is full (as soon as water touches black (100%) level sensor)
In Auto Mode the motor starts whenever the water level in overhead tank is less than 25% and stops when the overhead tank is full.
In Bypass Mode the motor is turned on directly. Motor will not be switched OFF automatically in this mode.
In OFF mode the controller is switched OFF
The Power ON indicator indicates whether device is ON or OFF.
The Lower Level Indicator lights up when water level in tank is above 25%
The Top Level Indicator lights up when water level in tank is above 100%
The Top Up switch is used for Manual On auto Off operation of motor. It works only in auto mode
The Stop switch is manually turn OFF the motor. It works only when water level is above 25% and only in Auto Mode
The Motor ON led lights up when motor is ON
Installation Circuit ( With SS Sensors)
You can watch detailed installation video just below this section.
Steps to install:
Measure the depth of the water tank by inserting the yellow sensor in it & mark it on yellow wire with a black tape
Now join the Green sensor at 25% level and black at 100% level (below the black tape) using small wire ties provided in the box.Make sure that black sensor is placed Overflow level of tank.
Now clip the extra part of wire ties and put this arrangement in the tank. To give proper support to this bundle of wires, tie it to a nearby pipeline using bigger wire ties.
Extend these sensor wires from overhead tank to device using a 3 core Signal wire . Alternatively if this wire is not available then you can use CAT6 (LAN wire) or CCTV wire or simple 3 core flexible electrical wire.
Now Mount the device on the wall.
Unscrew the Connectors and make the connections as described in installation circuit.
Connect 220V AC supply at input terminals. Connect Phase wire at P and Neutral wire at N. Do not interchange these connections.
Connect motor starter input terminals at output of controller device.
Finally screw the connectors tightly.
Installation Circuit with Magnetic Float Sensors
You can watch detailed installation video just below this section.
Steps to install:
Measure the Top level of tank by inserting Top magnetic float sensor & mark it with a black tape on it.
Now adjust the length of wire between the Lower sensor and top sensor such that Lower sensor is placed at 40% level and Top sensor at 100% level with help of small cable ties.
The Lower sensor float must be at 40% and top sensor float must be at 100%. Please ensure that 100% level is below the overflow level.
Now clip the extra part of wire ties and put this arrangement in the tank. To give proper support to this bundle of wires, tie it to a nearby pipeline using bigger wire ties.
Extend these sensor wires from overhead tank to device using a 3 core Signal wire . Alternatively if this wire is not available then you can use CAT6 (LAN wire) or CCTV wire or simple 3 core flexible electrical wire.
Now Mount the device on the wall.
Unscrew the Connectors and make the connections as described in installation circuit.
Connect 220V AC supply at input terminals. Connect Phase wire at P and Neutral wire at N. Do not interchange these connections.
Connect motor starter input terminals at output of controller device.
Finally screw the connectors tightly.
Prior to the final installation you should first take time to understand the working of this water level controller, Model- 1A_0020
Things you’ll need for this DIY test:
Water level controller
Two pcs of small wire
Screw driver
Electrical bulb with holder and wire ( For demo instead of Motor)
Steps to follow:
Connect 220V Ac supply at input terminals. Phase–P, Neutral–N
Connect electrical bulb at output terminals (Both Phase & Neutral)
Switch ON the power supply and keep the black switch in OFF position
Connect the one end of both wires and connect that end at L0.
Turn the switch position to AUTO –> As Green sensor is not connected Motor On Led is ON and Bulb is ON (i.e water level is low)
Connect one wire end at L1 —> 1st Led (25% level) will glow
Connect/ Touch other wire at L2 as shown in video —> Top Level Led (100% level) will glow & Motor On Led will be OFF & Bulb will also be OFF ( tank is Full )
Now turn the switch to Bypass Position –> Motor Led is ON i.e Bulb is ON irrespective of water level in the tank in Bypass Mode
Detailed video of How to Install IoTfiers – Water Level Controller (Model 1A_0020)
IoTfiers Fully automatic water level controller is suitable for Single Phase Submersible pumps (Borewell Type) upto 2 Hp with MCB type starter ( i.e Single Capacitor type starter). It requires no manpower to operate as it switches ON the motor when tank level is low (as soon as water falls below Green sensor) and automatically switches it OFF when the tank is full (as soon as water touches black (100%) level sensor)
In Auto Mode the motor starts whenever the water level in overhead tank is less than 25% and stops when the overhead tank is full.
In Bypass Mode the motor is turned on directly. Motor will not be switched OFF automatically in this mode.
In OFF mode the controller is switched OFF
The Power ON indicator indicates whether device is ON or OFF.
The Lower Level Indicator lights up when water level in tank is above 25%
The Top Level Indicator lights up when water level in tank is above 100%
The Top Up switch is used for Manual On auto Off operation of motor. It works only in auto mode
The Stop switch is manually turn OFF the motor. It works only when water level is above 25% and only in Auto Mode
The Motor ON led lights up when motor is ON
Installation Circuit ( With SS Sensors)
You can watch detailed installation video just below this section.
Steps to install:
Measure the depth of the water tank by inserting the yellow sensor in it & mark it on yellow wire with a black tape
Now join the Green sensor at 25% level and black at 100% level (below the black tape) using small wire ties provided in the box.Make sure that black sensor is placed Overflow level of tank.
Now clip the extra part of wire ties and put this arrangement in the tank. To give proper support to this bundle of wires, tie it to a nearby pipeline using bigger wire ties.
Extend these sensor wires from overhead tank to device using a 3 core Signal wire . Alternatively if this wire is not available then you can use CAT6 (LAN wire) or CCTV wire or simple 3 core flexible electrical wire.
Now Mount the device on the wall.
Unscrew the Connectors and make the connections as described in installation circuit.
Connect 220V AC supply at input terminals. Connect Phase wire at P and Neutral wire at N. Do not interchange these connections.
Connect motor starter input terminals at output of controller device.
Finally screw the connectors tightly.
Installation Circuit with Magnetic Float Sensors
You can watch detailed installation video just below this section.
Steps to install:
Measure the Top level of tank by inserting Top magnetic float sensor & mark it with a black tape on it.
Now adjust the length of wire between the Lower sensor and top sensor such that Lower sensor is placed at 40% level and Top sensor at 100% level with help of small cable ties.
The Lower sensor float must be at 40% and top sensor float must be at 100%. Please ensure that 100% level is below the overflow level.
Now clip the extra part of wire ties and put this arrangement in the tank. To give proper support to this bundle of wires, tie it to a nearby pipeline using bigger wire ties.
Extend these sensor wires from overhead tank to device using a 3 core Signal wire . Alternatively if this wire is not available then you can use CAT6 (LAN wire) or CCTV wire or simple 3 core flexible electrical wire.
Now Mount the device on the wall.
Unscrew the Connectors and make the connections as described in installation circuit.
Connect 220V AC supply at input terminals. Connect Phase wire at P and Neutral wire at N. Do not interchange these connections.
Connect motor starter input terminals at output of controller device.
Finally screw the connectors tightly.
No comments:
Post a Comment