Funding for this project continues from purchasing my Astro Gear. I write my ideas not to discredit anyone in the science/physics community of professionals, so I ask please be open-minded. When it comes to building a type of EM anti-gravity type, it's wrong, it's not the number of magnets, it's how much current you can apply to a magnet (coils) to increase the magnetic fields by repulsion induction, eg. opposing polarities. My idea, energizes the magnet (coils) increasing its magnetic field with the induced spin towards dielectric pitted (not smooth) plates, as a polarized flying capacitor energized by the magnetic field for lift. Power routes in series from the top and the bottom as positive to negative. Synergy is harnessed from the spinning array stator coils that charge the voltage multiplier capacitor banks. This build of banks reduces the craft's power-to-weight ratio to 5/1, with no need to have huge magnets and copper wire spools. How possible, is a strong surge of current, Lorentz force, R/C 10K rpm motors spinning energized Halbach array creates upwards lift, a downward repulsive magnetic field from the array creates a magnetic type of anti-gravity. I have created the frame using balsa wood to support the huge capacitor scaled at a height of 101mm, and a width of 254 mm consisting of 3 stacked arrays. I will need two R/C 10K RPM drives @ 12volts, no bigger than your 9-volt battery for this project. Create mounts for two 10K RPM drives. The first 10K drive will sit below the rotating array, 2nd the 10K RPM drive is for the top rotating array negating yaw. The 2nd counter-rotating arrays and static will have a few holes that may result in a Biefeld-Brown Effect. Install one ultrasonic emitter driver on top of the craft pointing downwards towards the big array where it is amplified by the EMF bubble canceling the craft's center of gravity outwards, hence the craft moves upward direction of EMF, bigger the EMF, bigger the encompassing lift, the craft becomes weightless. Applied HV to magnetic fields from the center coil, +/- lifts the flying capacitor up, a repulsion, anti-gravity, no, more like Newton's Law. This creates EMF radiating blueish glow below the craft, removes power, the capacitor array falls from mid-air, enables the voltage coil fields, and the craft rockets upwards, more like an electric drive, since its base construction is a magnetic coil. Having opposing poles in Halbach arrays, the polarities towards the middle static aluminum array increases EMF to thrust upwards. In this video, I have created a series of videos from the simplest basics of EMF to the end where we actually see the EMF thrust concept at work. This video is not here to argue the merits of gravity and not, but for those interested in making some type of anti-gravity using EMF, Ionic thrust, not the use of balloons, winged lifts, airplanes, and propelled thrusts. I share the idea of how to get started with electric hydrodynamics and dielectric materials, and hopefully, we can work together and get off this planet. So far, I have made a simple model of this and I did get a lift with a tethered power line. Secondly, I've taken a different approach with the Proto 13 project, building my basic EMF drive
Funding for this project continues from purchasing my Astro Gear. I write my ideas not to discredit anyone in the science/physics community of professionals, so I ask please be open-minded. When it comes to building a type of EM anti-gravity type, it's wrong, it's not the number of magnets, it's how much current you can apply to a magnet (coils) to increase the magnetic fields by repulsion induction, eg. opposing polarities. My idea, energizes the magnet (coils) increasing its magnetic field with the induced spin towards dielectric pitted (not smooth) plates, as a polarized flying capacitor energized by the magnetic field for lift. Power routes in series from the top and the bottom as positive to negative. Synergy is harnessed from the spinning array stator coils that charge the voltage multiplier capacitor banks. This build of banks reduces the craft's power-to-weight ratio to 5/1, with no need to have huge magnets and copper wire spools. How possible, is a strong surge of current, Lorentz force, R/C 10K rpm motors spinning energized Halbach array creates upwards lift, a downward repulsive magnetic field from the array creates a magnetic type of anti-gravity. I have created the frame using balsa wood to support the huge capacitor scaled at a height of 101mm, and a width of 254 mm consisting of 3 stacked arrays. I will need two R/C 10K RPM drives @ 12volts, no bigger than your 9-volt battery for this project. Create mounts for two 10K RPM drives. The first 10K drive will sit below the rotating array, 2nd the 10K RPM drive is for the top rotating array negating yaw. The 2nd counter-rotating arrays and static will have a few holes that may result in a Biefeld-Brown Effect. Install one ultrasonic emitter driver on top of the craft pointing downwards towards the big array where it is amplified by the EMF bubble canceling the craft's center of gravity outwards, hence the craft moves upward direction of EMF, bigger the EMF, bigger the encompassing lift, the craft becomes weightless. Applied HV to magnetic fields from the center coil, +/- lifts the flying capacitor up, a repulsion, anti-gravity, no, more like Newton's Law. This creates EMF radiating blueish glow below the craft, removes power, the capacitor array falls from mid-air, enables the voltage coil fields, and the craft rockets upwards, more like an electric drive, since its base construction is a magnetic coil. Having opposing poles in Halbach arrays, the polarities towards the middle static aluminum array increases EMF to thrust upwards. In this video, I have created a series of videos from the simplest basics of EMF to the end where we actually see the EMF thrust concept at work. This video is not here to argue the merits of gravity and not, but for those interested in making some type of anti-gravity using EMF, Ionic thrust, not the use of balloons, winged lifts, airplanes, and propelled thrusts. I share the idea of how to get started with electric hydrodynamics and dielectric materials, and hopefully, we can work together and get off this planet. So far, I have made a simple model of this and I did get a lift with a tethered power line. Secondly, I've taken a different approach with the Proto 13 project, building my basic EMF drive
No comments:
Post a Comment