This video shows how to make the battery charger automatically turn on and off.
Ingredients used:
1. 1pcs 12V Relay
2. BC547 NPN Transistors
3. Resistor 1K ohm 1pcs
4. 100 ohm resistor 1pcs
5. 5K ohm resistor 1pcs
6. Potentiometer 5K ohm 1pcs
7. 2pcs 5mm leds
This series is very easy to make at home.
And this automatic charger can be adjusted for its cut-off voltage.
Before starting the charger must be set according to the cut off voltage we want.
And the battery must be installed first and then the charger input.
For details, you can see the video.
Automatic 12 Volt Battery Charger
How to set XH-M601 12V┃12V battery charger automatically cut off and ON
controller accu charging battery
This video explains how to set the XH-M601 the most correctly, and you can set the ON Off value as you wish.
Why is setting this module a little complicated, this is because of the nature of the main IC used, namely IC 555... Good luck
12 volt auto cut off battery charger,12 volt automatic battery charger,12 volt battery level indicator,12v auto cut off battery charger circuit,12v battery charger circuit with auto cut off,12v battery charger kaise banaye,12v battery full charge indicator,auto cut off 12v battery charger, auto cut off battery charger, auto cut off 12v battery charger, automatic 12v battery charger, how to make 12v battery charger auto cut off, how to make auto cut off battery charger
XH-M601 Automatic Charger Control Module for Auto Cut Off battery
This is how the 12V display battery charger works
car motorcycle battery charger module digital LCD display automatic cut off 30A
Features:
1.Support Lead-acid battery and Acting Battery,voltage range:6V~60V;
2. Can display voltage,percent of battery,charging time at the same time through LCD
3.The function is very powerful,realizes the automatic charge control,the control charge time, also may set up and uploads the corresponding parameter through the serial port
Specifications:
Product Model: XY-L10A
Controlvoltage:DC6-60V
Control current: less than 10A
Control accuracy:0.1V
Output Type: Direct Output
Voltage error:±0.1V
Scope of application: various lithium batteries
1.Automatic Charge control function：
By setting the volt-HI:'UP' volt-LI:'dn';When the battery voltage is below the volt-LI:'dn',the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:'UP',the relay is connected and the automatic charge is completed once
a)Press and hold the SET key to enter the setting interface;
b)Switch the parameters you want to set by short press SET;
c) After the selection of parameters, can be set by the UP/DOWN key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c);
d)After all parameters are set, long press set key to exit and save;
In the Run interface (main interface):
Short press SET button to display the current set of parameters; Short press the UP button, toggle display charge percentage and charging time;
Short Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, it will show 'off' as a reminder;
Long press the UP button, switch low power state
on：No operation in 10 minutes turn off backlight
OFF: Backlight is always bright
Long press SET button,enter the parameter settings.
voltage percentage = battery voltage/(volt-HI – volt-LI)
12V Automatic Accu / Cas Battery Charger Kit Module Up To 150A Cheap
Product Parameters:
1: Power supply voltage: DC6--40V, voltage detection range DC 0--60V, suitable for less than 60V of the various batteries, voltage measurement error 0.1V.
2: charge and discharge time (OP) range: 0 - 999 minutes.
Operating Modes:
Voltage upper limit: UL1, voltage lower limit nL1, the voltage upper limit is greater than the voltage lower limit (UL1 is less than nL1)
U-1: Charging measurement: When the measured voltage is lower than the lower limit voltage, the relay pulls above; the upper limit voltage, the relay is disconnected.
U-2: charge measurement time control: set the charging time (OP); when the measured voltage is lower than the lower limit voltage, the relay pulls, and then starts the countdown OP time, the end of the timer, the relay off; when the measured voltage is higher than the upper limit voltage , the relay is disconnected.
U-3: Discharge detection: When the measured voltage is lower than the lower limit voltage, the relay is off, above the upper limit voltage, the relay pulls;
U-4: discharge detection time control: set the discharge time (OP); when the measured voltage is higher than the upper limit voltage, the relay pulls, and then starts the countdown OP time, the end of the timer, the relay off; when the measured voltage is below the lower limit voltage , the relay is disconnected;
U-5: voltage in the range, the relay pull: when the measured voltage between the upper and lower limits, the relay pulls, the other circumstances open;
U-6: voltage outside the interval, the relay pull: the measured voltage below the lower limit voltage or higher than the upper limit voltage, the relay pulls, the other case the relay is off.
This video shows how to make the battery charger automatically turn on and off.
Ingredients used:
1. 1pcs 12V Relay
2. BC547 NPN Transistors
3. Resistor 1K ohm 1pcs
4. 100 ohm resistor 1pcs
5. 5K ohm resistor 1pcs
6. Potentiometer 5K ohm 1pcs
7. 2pcs 5mm leds
This series is very easy to make at home.
And this automatic charger can be adjusted for its cut-off voltage.
Before starting the charger must be set according to the cut off voltage we want.
And the battery must be installed first and then the charger input.
For details, you can see the video.
Automatic 12 Volt Battery Charger
How to set XH-M601 12V┃12V battery charger automatically cut off and ON
controller accu charging battery
This video explains how to set the XH-M601 the most correctly, and you can set the ON Off value as you wish.
Why is setting this module a little complicated, this is because of the nature of the main IC used, namely IC 555... Good luck
12 volt auto cut off battery charger,12 volt automatic battery charger,12 volt battery level indicator,12v auto cut off battery charger circuit,12v battery charger circuit with auto cut off,12v battery charger kaise banaye,12v battery full charge indicator,auto cut off 12v battery charger, auto cut off battery charger, auto cut off 12v battery charger, automatic 12v battery charger, how to make 12v battery charger auto cut off, how to make auto cut off battery charger
XH-M601 Automatic Charger Control Module for Auto Cut Off battery
This is how the 12V display battery charger works
car motorcycle battery charger module digital LCD display automatic cut off 30A
Features:
1.Support Lead-acid battery and Acting Battery,voltage range:6V~60V;
2. Can display voltage,percent of battery,charging time at the same time through LCD
3.The function is very powerful,realizes the automatic charge control,the control charge time, also may set up and uploads the corresponding parameter through the serial port
Specifications:
Product Model: XY-L10A
Controlvoltage:DC6-60V
Control current: less than 10A
Control accuracy:0.1V
Output Type: Direct Output
Voltage error:±0.1V
Scope of application: various lithium batteries
1.Automatic Charge control function：
By setting the volt-HI:'UP' volt-LI:'dn';When the battery voltage is below the volt-LI:'dn',the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:'UP',the relay is connected and the automatic charge is completed once
a)Press and hold the SET key to enter the setting interface;
b)Switch the parameters you want to set by short press SET;
c) After the selection of parameters, can be set by the UP/DOWN key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c);
d)After all parameters are set, long press set key to exit and save;
In the Run interface (main interface):
Short press SET button to display the current set of parameters; Short press the UP button, toggle display charge percentage and charging time;
Short Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, it will show 'off' as a reminder;
Long press the UP button, switch low power state
on：No operation in 10 minutes turn off backlight
OFF: Backlight is always bright
Long press SET button,enter the parameter settings.
voltage percentage = battery voltage/(volt-HI – volt-LI)
12V Automatic Accu / Cas Battery Charger Kit Module Up To 150A Cheap
Product Parameters:
1: Power supply voltage: DC6--40V, voltage detection range DC 0--60V, suitable for less than 60V of the various batteries, voltage measurement error 0.1V.
2: charge and discharge time (OP) range: 0 - 999 minutes.
Operating Modes:
Voltage upper limit: UL1, voltage lower limit nL1, the voltage upper limit is greater than the voltage lower limit (UL1 is less than nL1)
U-1: Charging measurement: When the measured voltage is lower than the lower limit voltage, the relay pulls above; the upper limit voltage, the relay is disconnected.
U-2: charge measurement time control: set the charging time (OP); when the measured voltage is lower than the lower limit voltage, the relay pulls, and then starts the countdown OP time, the end of the timer, the relay off; when the measured voltage is higher than the upper limit voltage , the relay is disconnected.
U-3: Discharge detection: When the measured voltage is lower than the lower limit voltage, the relay is off, above the upper limit voltage, the relay pulls;
U-4: discharge detection time control: set the discharge time (OP); when the measured voltage is higher than the upper limit voltage, the relay pulls, and then starts the countdown OP time, the end of the timer, the relay off; when the measured voltage is below the lower limit voltage , the relay is disconnected;
U-5: voltage in the range, the relay pull: when the measured voltage between the upper and lower limits, the relay pulls, the other circumstances open;
U-6: voltage outside the interval, the relay pull: the measured voltage below the lower limit voltage or higher than the upper limit voltage, the relay pulls, the other case the relay is off.
No comments:
Post a Comment