on video LED Circuit Design - How to Design LED Circuits

 

LED Circuit Design - How to Design LED Circuits

LED Circuit Design - How to Design LED Circuits. How to calculate resistor sizes, how to protect LEDs, how long will a battery power a circuit, how to calculate resistor power ratings, how to connect LEDs and much more.

How to power LEDs?

For each diode (LED) to operate, a voltage across its terminals of approximately 3 Volt is required. If the series includes 5 diodes, for example, the voltage across it should be about 15 Volt. To provide this regulated current under a sufficient voltage, LEC sets up an electronic module called a driver.

How to wire an LED?

Connection to the switch

Connect the neutral (blue wire) to the transformer (terminal N). If necessary, connect the earth (yellow/green wire) to the transformer (Earth icon terminal). Connect the + terminal of the transformer to the LED strip (+12V terminal). Connect the - terminal of the transformer to the LED strip (-12V terminal).

How to power a 220V LED?

How to connect a 220V LED bulb? All you need is a resistor and a diode to connect a 230V LED (first 220V) directly to the mains.

How to power a 3V LED?

Re: Reduce a voltage from 5V to 3V to power a led

The principle is to put your voltage source U in series with R1 and R2 then to take the voltage across R2 which will then be equal to U*R2/(R1+R2) .

Found 26 related questions

Why put a resistor in front of an LED?

It makes it possible to reduce the supply voltage (like a transformer delivering 12V in direct current) in order to obtain the voltage necessary to illuminate a led (for example 2.3V). Be careful, the value of a resistor is calculated in relation to what you want to supply.

How to connect LEDs without a plug?

Connect the switch Connect the switch (blue wire) to the translator (terminal N). If necessary, connect the earth (yellow/green wire) and the transformer (terminal earth symbols). Connect the translation cable to the LED cable terminal (12V terminal). Connect – LED translation terminal (-12V terminal).

How to connect an LED ribbon without a transformer?

Connecting an LED strip without a transformer

The 220V LED ribbon is connected directly to a completely normal electrical outlet. Generally, the 220V LED strip is sectioned every 50 cm and it is possible to reuse the cut sections by means of a connection kit

How to connect 12V LED?

How to connect an LED to 12V?

Select the base of the bulb in question. …

Remove the bulb.

Find the 12V transformer. …

Get rid of the old. …

Assemble the sleeve.

Assemble the sleeve. …

Connect the power supply to the 220V network. …

Replace the bulb in its holder.

What resistor to power a 12V LED?

For our example (3mm green LED) this gives under 12V: 435 ohms. Then just take the nearest upper resistor, in this case, we will have to choose a resistance of 470 ohm. This value will be necessary for you to choose the right resistance in the site

Why a transformer for LED?

Having an LED transformer (power supply, driver) is essential in order to maintain optimal performance and guarantee the reliability of the LED(s).

How to connect several LEDs together?

How to solder 2 LED strips? Just put the tin wires and LED tape on the connector then attach the metal to the connector, then the tin on both sides will be liquefied and mixed, and the cables will be sealed and sold with cooling.

What is the voltage of an LED lamp?

The supply voltages for LED lighting are in most cases 220V, 12V or 24V.

How to install an LED transformer?

To connect the socket to the electronic transformer, take the output of the transformer (the two white wires which are already connected to the origin on the transformer) and connect them to the domino of the socket.

How to calculate the voltage of an LED?

The calculation is a simple application of Ohm's law and is done in two stages. We first calculate the voltage drop necessary for the led diode to be subjected to a direct voltage of 2.1 V: UR=U(Alim)−Vf. Let: UR=5−2.1=2.9 V.

How to know the power of an LED?

hello, either a red led (red led -> terminal voltage = 1.8V) powered at 5V with a resistor R in series. we chose 330 ohms (standard value) the intensity is therefore (5V- 1.8v) /330=9.6 mA. resistance (dynamic) of the LED =1.8/0.0096=188 ohms.

How to calculate the watts of an LED?

Calculation of the consumption of an LED bulb

10 W/1000 (1 watt = 0.001 kWh) x 3 (hours per day) x 30 (days in the month) = 0.9 kWh/month. We must therefore multiply 0.9 by the price of the kWh of electricity to obtain the of the monthly consumption of an LED bulb.

How to choose a transformer for LED?

Which transformer power to choose? You must first calculate the total power of all the elements that will be powered by the transformer, in our case 5 bulbs of 5 watts. So the choice of the transformer having the closest necessary power is a specific 30 watt LED transformer.

How to connect LEDs to a battery?

How to connect LEDs to a battery? It is possible to connect an LED to a battery: all you need is a resistor and a small electric cable. The connection is made in a sort of battery – resistor – LED loop. This is a series circuit where the resistor is connected in series with the LED

Why does an LED strip not work?

When an LED strip no longer lights up after you have tested it on different types of power supply, it is good for the trash. The second sign is the presence of shadow spots along the ribbon. If these spots are too close to each other, the ribbon is no longer salvageable.

How to power an LED strip with batteries?

Power LED plug

This "Plug" power supply will plug directly into a standard 220V socket. It will look like a cell phone charger. It is available in 5V, 12V, 24V and will generally be used when low power is needed.

How to connect an LED ribbon to the ceiling?

To install an LED ribbon on the ceiling of the bedroom, you can opt for two fixing methods. The first is to simply remove the backing from one side of your adhesive light strip and attach it to the ceiling. The second offers better fixation, but takes longer to put in place.

How to make cut LEDs work?

All you have to do is open the connector and place the two LED strips inside. Once they are inside, all you have to do is close the connector, and it will take care of the connection between the two strips! That's it, the connection is established!

 

LED Circuit Design - How to Design LED Circuits

LED Circuit Design - How to Design LED Circuits. How to calculate resistor sizes, how to protect LEDs, how long will a battery power a circuit, how to calculate resistor power ratings, how to connect LEDs and much more.

How to power LEDs?

For each diode (LED) to operate, a voltage across its terminals of approximately 3 Volt is required. If the series includes 5 diodes, for example, the voltage across it should be about 15 Volt. To provide this regulated current under a sufficient voltage, LEC sets up an electronic module called a driver.

How to wire an LED?

Connection to the switch

Connect the neutral (blue wire) to the transformer (terminal N). If necessary, connect the earth (yellow/green wire) to the transformer (Earth icon terminal). Connect the + terminal of the transformer to the LED strip (+12V terminal). Connect the - terminal of the transformer to the LED strip (-12V terminal).

How to power a 220V LED?

How to connect a 220V LED bulb? All you need is a resistor and a diode to connect a 230V LED (first 220V) directly to the mains.

How to power a 3V LED?

Re: Reduce a voltage from 5V to 3V to power a led

The principle is to put your voltage source U in series with R1 and R2 then to take the voltage across R2 which will then be equal to U*R2/(R1+R2) .

Found 26 related questions

Why put a resistor in front of an LED?

It makes it possible to reduce the supply voltage (like a transformer delivering 12V in direct current) in order to obtain the voltage necessary to illuminate a led (for example 2.3V). Be careful, the value of a resistor is calculated in relation to what you want to supply.

How to connect LEDs without a plug?

Connect the switch Connect the switch (blue wire) to the translator (terminal N). If necessary, connect the earth (yellow/green wire) and the transformer (terminal earth symbols). Connect the translation cable to the LED cable terminal (12V terminal). Connect – LED translation terminal (-12V terminal).

How to connect an LED ribbon without a transformer?

Connecting an LED strip without a transformer

The 220V LED ribbon is connected directly to a completely normal electrical outlet. Generally, the 220V LED strip is sectioned every 50 cm and it is possible to reuse the cut sections by means of a connection kit

How to connect 12V LED?

How to connect an LED to 12V?

Select the base of the bulb in question. …

Remove the bulb.

Find the 12V transformer. …

Get rid of the old. …

Assemble the sleeve.

Assemble the sleeve. …

Connect the power supply to the 220V network. …

Replace the bulb in its holder.

What resistor to power a 12V LED?

For our example (3mm green LED) this gives under 12V: 435 ohms. Then just take the nearest upper resistor, in this case, we will have to choose a resistance of 470 ohm. This value will be necessary for you to choose the right resistance in the site

Why a transformer for LED?

Having an LED transformer (power supply, driver) is essential in order to maintain optimal performance and guarantee the reliability of the LED(s).

How to connect several LEDs together?

How to solder 2 LED strips? Just put the tin wires and LED tape on the connector then attach the metal to the connector, then the tin on both sides will be liquefied and mixed, and the cables will be sealed and sold with cooling.

What is the voltage of an LED lamp?

The supply voltages for LED lighting are in most cases 220V, 12V or 24V.

How to install an LED transformer?

To connect the socket to the electronic transformer, take the output of the transformer (the two white wires which are already connected to the origin on the transformer) and connect them to the domino of the socket.

How to calculate the voltage of an LED?

The calculation is a simple application of Ohm's law and is done in two stages. We first calculate the voltage drop necessary for the led diode to be subjected to a direct voltage of 2.1 V: UR=U(Alim)−Vf. Let: UR=5−2.1=2.9 V.

How to know the power of an LED?

hello, either a red led (red led -> terminal voltage = 1.8V) powered at 5V with a resistor R in series. we chose 330 ohms (standard value) the intensity is therefore (5V- 1.8v) /330=9.6 mA. resistance (dynamic) of the LED =1.8/0.0096=188 ohms.

How to calculate the watts of an LED?

Calculation of the consumption of an LED bulb

10 W/1000 (1 watt = 0.001 kWh) x 3 (hours per day) x 30 (days in the month) = 0.9 kWh/month. We must therefore multiply 0.9 by the price of the kWh of electricity to obtain the of the monthly consumption of an LED bulb.

How to choose a transformer for LED?

Which transformer power to choose? You must first calculate the total power of all the elements that will be powered by the transformer, in our case 5 bulbs of 5 watts. So the choice of the transformer having the closest necessary power is a specific 30 watt LED transformer.

How to connect LEDs to a battery?

How to connect LEDs to a battery? It is possible to connect an LED to a battery: all you need is a resistor and a small electric cable. The connection is made in a sort of battery – resistor – LED loop. This is a series circuit where the resistor is connected in series with the LED

Why does an LED strip not work?

When an LED strip no longer lights up after you have tested it on different types of power supply, it is good for the trash. The second sign is the presence of shadow spots along the ribbon. If these spots are too close to each other, the ribbon is no longer salvageable.

How to power an LED strip with batteries?

Power LED plug

This "Plug" power supply will plug directly into a standard 220V socket. It will look like a cell phone charger. It is available in 5V, 12V, 24V and will generally be used when low power is needed.

How to connect an LED ribbon to the ceiling?

To install an LED ribbon on the ceiling of the bedroom, you can opt for two fixing methods. The first is to simply remove the backing from one side of your adhesive light strip and attach it to the ceiling. The second offers better fixation, but takes longer to put in place.

How to make cut LEDs work?

All you have to do is open the connector and place the two LED strips inside. Once they are inside, all you have to do is close the connector, and it will take care of the connection between the two strips! That's it, the connection is established!